Seeing a tE error code appear on your oven display can raise some alarm bells. But while these error codes may seem scary, the problem is typically an easy fix with some DIY troubleshooting.
We’ll explore the common causes of tE errors and walk through the steps to diagnose and resolve the issue in your oven. With a few simple tools and component replacements, you can likely have your appliance heating properly again.
Contents hide
I How to fix a tE error code on your Samsung oven
I.I tE error code meaning
I.II Troubleshooting
I.III Checking oven thermostats
I.IV Inspect electrical connections
I.V Replace the oven control board
I.VI Verifying repair success
I.VII Preventing future tE error codes
I.VIII More information
I.VIII.I Share this entry
tE error code meaning
The tE error code indicates an issue with the oven temperature sensor circuit. This is the part responsible for monitoring the internal oven temperature and reporting it back to the control board.
Some common causes for tE oven errors include:
- Faulty or damaged temperature sensor
- Broken sensor wiring connections
- Defective oven thermostat
- Failed oven control board
When the control board stops getting accurate temperature data, it’ll turn off the heating elements and show the tE alert for you to check out.
READ MORE: How to prevent appliance fire hazards
Troubleshooting
The oven temperature sensor is one of the main causes of tE errors. Here’s a guide on how to test it:
- Turn off the oven power supply at the breaker. Verify it is fully disconnected.
- Remove the back oven panel to access the sensor wiring and connections. Check your tech sheet or wiring diagram to assist with this.
- Detach the sensor wiring from the main control board connection.
- Use a multimeter and check the sensor resistance at room temperature. Generally, the reading should be around 1000 to 1100 ohms but don’t forget to consult the tech sheet for your appliance to get an accurate reading.
- Inspect the temperature sensor and wiring for any damage that could prevent accurate readings.
If the temperature sensor checks out, proceed to inspect oven thermostats and electrical connections.
READ MORE: How To Use A Multimeter
Checking oven thermostats
Dual oven models have a main temperature control thermostat and a secondary thermostat. Issues with either could produce a tE code.
Use a multimeter to check both thermostat units for continuity. The part should read closed for continuity, if it shows open or has an infinite resistance the part will need to be replaced.
Make sure the thermostat wiring is intact and properly connected. Damaged wiring can cause temperature sensor errors. Damaged wiring would need to be replaced.
READ MORE: 4 Simple Ways to Reduce Kitchen Waste
Inspect electrical connections
The wiring for the temperature sensor ends at connections on the main oven control board.
Closely examine where the sensor wiring plugs into the control board. Reseat any loose connections firmly. Check that the wire terminals are crimped tightly and are free of corrosion.
Look for any signs of damaged wires or indications of overheating that could suggest faulty wiring. If any wiring is found to be damaged, replace it as necessary.
READ MORE: 8 DIY Safety Tips
Replace the oven control board
If sensor connections are sound and thermostats are good, the main control board will be the issue. Shorts or faulty components on the board can mimic temperature sensor errors.
Consult your oven’s service manual for proper board removal and installation. Grab your model number and go to AppliancePartsPros.com to locate the correct part for your model.
Verifying repair success
After replacing any components, reconnect the oven power and verify the unit is heating properly and the error code does not return.
Run the oven through several cycles to make sure it maintains set temps without any tE code reappearing. The error should be cleared for good.
Carefully reinstall the oven back panel once testing is complete. You can now safely use your oven again for cooking.
READ MORE: 10 Tips and Tricks to Clean Your Appliances
Preventing future tE error codes
To help avoid tE errors going forward:
- Maintain your oven cleanliness to prevent debris buildup on the temperature sensor.
- Handle oven parts gently during cleaning and replacement to avoid damaging wiring.
- Only operate your oven within its maximum heat rating to avoid component degradation.
With proper troubleshooting and care, tE temperature sensor errors can be easily cleared up.
READ MORE: Thanksgiving appliance checklist: What to check and fix before the holiday
More information
Thanks for reading! If you have any other appliance repair needs or projects, you can find more resources including our DIY blog at AppliancePartsPros.com. There, you can enter your model number to order the exact parts you need. Most orders arrive in two business days.
You can also reach our award-winning customer service team at 1-877-477-7278, chat with a pro on our website and watch thousands of free video tutorials on our YouTube channel.